Exposed-Fastener, 5V and Corrugated Metal Roofing in Macon, GA

Exposed-fastener metal roofing is the classic Southern metal roof: 5V crimp on a farmhouse, corrugated on a barn, R-panel on a shop or carport. The panels are screwed straight through to the deck or purlins, so it costs less than standing seam and goes on faster. Call (478) 330-3652 and we will connect you with an independent local contractor who installs exposed-fastener metal roofs on homes, barns, shops and outbuildings across Macon and Middle Georgia. We are a referral service; the contractor quotes and does the work.

Panel styles

5V crimp

Flat panels with five V-shaped ribs. 5V is a traditional look on older Georgia farmhouses and cottages, and it is often chosen to match the character of older homes.

Corrugated

Wavy, rounded ribs. Common on barns, sheds, porches and rustic-style homes.

R-panel and PBR

Taller trapezoid ribs that span farther between purlins. Common on shops, pole barns, garages and light commercial buildings.

Good uses

• Budget-conscious homeowners who want metal on a house.
• Farmhouse, cabin and lake-house styles.
• Barns, equipment sheds and horse barns in rural Bibb, Jones, Monroe and Houston counties.
• Detached shops, garages, carports and porches.
• Replacing rusted old tin on outbuildings.

The trade-off: screws and washers

Every panel is held down by screws with rubber or EPDM washers. Over years of Georgia sun and heat, those washers can harden and crack, and screws can back out as the metal expands and contracts every day. That is the most common source of leaks on exposed-fastener roofs. It is not a reason to avoid this roof; it just means the screws should be checked every few years and replaced or upsized when they loosen. Ask the contractor about long-life fasteners and how many screws per panel they use.

How it is installed

1. Inspect and measure the roof, deck or framing.
2. Tear off old shingles or rusted metal if needed.
3. On houses: install synthetic underlayment over solid decking. On barns and shops: install purlins and, where needed, a condensation control layer or insulation.
4. Set eave trim and closure strips.
5. Lay panels with the correct overlap, square to the eave, and fasten in the flat or on the rib as the manufacturer specifies.
6. Install ridge cap, gable trim and vent boots.
7. Sweep for screws and scraps.

What exposed-fastener metal roofing costs

Typical national-guide ranges. Always get a written quote.

What drives the price

• Steel gauge (29 gauge is common and cheaper; 26 gauge is heavier and stiffer).
• Painted vs. bare Galvalume finish.
• Tear-off of shingles or old rusted tin.
• Condition of decking, rafters or purlins.
• Height, pitch and access, especially for tall barns.
• Trim details such as gable trim, sidewall flashing and closures.

How long it takes

A simple shed, carport or porch is often done in a day. A barn or shop may take two to four days. Many average homes take about two to five working days, plus lead time for materials.

Middle Georgia conditions that matter for a metal roof

• Heat and humidity. Long, hot, humid summers bake roofs from May into October. Metal with a reflective (cool-roof) paint finish sheds more heat than dark shingles, and good attic ventilation and underlayment help control condensation under the panels.
• Severe thunderstorms, hail and the occasional tornado. Spring and summer storms bring strong wind gusts, and hail and tornado warnings are part of life in Middle Georgia. Ask about the wind rating of the panel system, the fastener or clip spacing, and whether a hail-impact-rated (Class 4) product is offered, since some insurers recognize it.
• Tall pines and oaks. Many lots in Bibb, Houston, Jones and Monroe counties sit under mature pines and water oaks. Falling limbs, pine straw, leaves and shade-driven moss and algae are all factors. Valleys and gutters need regular cleaning, and overhanging limbs should be trimmed before a new roof goes on.
• Older homes and historic districts. Macon has large historic districts, including Intown Macon, Vineville and Ingleside. If your home is in one, design review may apply to a roof change. Check with Macon-Bibb County's historic preservation staff before you sign a contract.
• Licensing and permits. Georgia requires residential contractors to hold a state license for larger jobs. Ask any contractor for the license and proof of liability and workers' compensation insurance, and ask whether a Macon-Bibb (or your county's) building permit is needed and who pulls it.

Tips for barns and shops

• Ask about condensation control. Uninsulated metal over a barn or shop can drip on hot, humid nights.
• Keep fertilizer, manure and lime off the panels; they can attack the coating.
• Use a contractor who knows the difference between residential decking and purlin framing.
• Check screws after a few years and after big wind storms.

Call (478) 330-3652 to reach a local contractor for a 5V, corrugated or R-panel metal roof.

Frequently asked questions

Areas we serve

We connect callers across Macon, Warner Robins, Perry, Forsyth and Middle Georgia, including:

• Macon
• Warner Robins
• Perry
• Forsyth
• Byron
• Centerville
• Kathleen
• Bonaire
• Gray
• Lizella
• Jones County
• Houston County
• Bibb County
• Monroe County
• Middle Georgia

Local pages: Warner Robins, Perry, Forsyth.

Related services

• Standing Seam Metal Roofs
• Shingle-to-Metal Roof Replacement
• Commercial & Agricultural Metal Roofing
• Metal Roof Repair & Leaks
• Metal Roof Coatings & Restoration